How to Install a LED Strip

Practical to install, low consumption and looks modern and appealing.

Are LED strips, also known as LED strip, that help illuminate, often so imaginative and decorative, different parts of the House.

LED strips allow daylight thanks to LED light bulbs present on their surface and haveprecise specifications.

Characteristics of LED strips

LED strips come in the form of roll, generally does not exceed five metres in length(some examples on Amazon).On the surface of the LED strip LED lighting chips are soldered. The strips are usually cut into pieces to be applied on the to be decorated.

Every 5 mm Strip, within which there are three LEDs, is in fact a cut off point.

This means that for example in one meter of LED strip 60 LED are present while on afive-meter strip the chips will be 300.

Each piece of the Strip can be managed and implemented according to your needs,to obtain the desired lighting or to create the decorations that we like.

Moreover, thanks to their physical characteristics, the LED strip can be applied everywhere, even where normal lamps cannot be placed, says itypeusa.

LED strips are extremely flexible and above all have much smaller both in width, which generally is about ten to twelve millimeters, which in thickness, usually no more than two millimeters.

For these reasons, LED strips can also be applied following the curves or corners.

In any case, we must be careful not to place the Strip curves of RADIUS less than one centimeter, so as not to damage the components of the strip.

As for energy consumption, the one generated by LED strips is pretty low. A strip ofone meter, for example, has a power of 3.6 watts to which that of a unit of five centimeters will be about 0.18 watts.

As a result, the length of the Strip will be quite extensive, with approximately 50,000hours life. The voltage is 12 volts.

The tension LED bulbs can also be diminished, slightly lowering the brightness, andthus to a consumption of just 1 watt per meter strip.

LED bulbs also do not generate heat, especially in the case of stripes usually permeable.

Those raincoats instead feature a thermal insulation that helps to raise the temperature of the LEDs while they are running. On the other hand, waterproof strips are indicated if the Strip must be installed near water sources, for example in the bathroomor in the kitchen. Finally the colors. LED bulbs may present different shades, from white until you get to the yellow, red, blue and so on.

The different colors depend on different machine processes of light and are used primarily to enhance the decorative value of the Strip.

Use and installation of LED Strip

As already mentioned, LED strips, with their attractive appearance and original with the colors rendered particularly gaudy and filled with lighting, possess a high decorative value and are now widely used just to provide a particular lighting environments.

By combining pieces of different tones you can get various decorations and also create real designs, following their fantasy.

But in addition to constitute an added value from the point of view of aesthetics, LED strips because of their ease of application can also provide a lighting system where place a normal lamp would be very difficult.

Is the very tight corners, curves or areas where the ceilings are quite low and even a simple ceiling light would clutter. In addition, the strips evenly diffused light LEDs provide even larger environments or rectangular in shape.

Following the profile of the ceilings, for example, the LED strip can create expansescapable of reaching every side of the room. The installation of LED strips then is quite simple and affordable for everyone. The application of the strip is facilitated by the presence of a sticker on the back. Removing the protective paper strip, you can safely place the strip by doing a simple pressure to adhere the tape to the surface to be decorated.

A bit fancier is the electrical connection. LED Strip must be connected to a transformer of energy from 220 to 12 volts. When connecting the transformer, you must take care to respect the polarity marked on the LED Strip, the positive and the negative.

The General system connection is by adding a switch, which will be merged with theexisting doing a bridge with blue wire; even the other wire, Brown, should be connected to the switch in order to switch on and off.

The transformer will be connected to the other two wires.

The various pieces of the Strip must be joined together, to create a bridge, by welding together the wires on the terminals, using a soldering iron. In this way you will get stripes of variable length and can be adapted to various needs.

Very important is also the point of the Strip where you made the connection with the transformer.

If indeed this is attached to only one side of the Strip, the LEDs are brighter because it will receive much more energy while those placed on the opposite side will have a weaker light.

This happens especially when the Strip is very long and one of the consequences is an overload voltage that causes a shorter life span of LEDs.

To avoid all this, just connect it to the center of the Strip, bringing the power on both sides of the strip.

Gallery

How to Install Interior RAZIR LED Lights and Strip Kits …

How to Install Interior RAZIR LED Lights and Strip Kits ...

Source: www.youtube.com

Portable Canopy Tent Lighting With LED Strip Lights Kit …

Portable Canopy Tent Lighting With LED Strip Lights Kit ...

Source: www.superbrightleds.com

Fiber Optics Lighting

Fiber Optics Lighting

Source: decorlighting.port-media.org

Led Recessed Lighting Wiring Diagram

Led Recessed Lighting Wiring Diagram

Source: www.imageresizertool.com

How To Install Cove Lighting — 1000Bulbs.com Blog

How To Install Cove Lighting — 1000Bulbs.com Blog

Source: blog.1000bulbs.com

Australian bathrooms lighting requirements, regulations

Australian bathrooms lighting requirements, regulations

Source: edisonlightglobes.com

Light Fixture Mounting Bracket. How To Install Ceiling …

Light Fixture Mounting Bracket. How To Install Ceiling ...

Source: royalfeathers.com

Fluorescent Lighting: How to Install Fluorescent Light …

Fluorescent Lighting: How to Install Fluorescent Light ...

Source: www.epiphanots.com

240 Volt Heater Wiring Diagram – vivresaville.com

240 Volt Heater Wiring Diagram – vivresaville.com

Source: www.vivresaville.com

Looking to upgrade my stock headlights!

Looking to upgrade my stock headlights!

Source: www.f150forum.com

How to Choose The Best Under Cabinet Lighting

How to Choose The Best Under Cabinet Lighting

Source: sebringdesignbuild.com

Wiring Diagram For Under Cabinet Lighting Cable For Under …

Wiring Diagram For Under Cabinet Lighting Cable For Under ...

Source: www.odicis.org

Fire Tv Rooted Amazon Fire Review – rastreo.com.co

Fire Tv Rooted Amazon Fire Review – rastreo.com.co

Source: rastreo.com.co

EXVB 3G1,5 /meter

EXVB 3G1,5 /meter

Source: www.tecshop.be

Fire Tv Rooted Amazon Fire Review – rastreo.com.co

Fire Tv Rooted Amazon Fire Review – rastreo.com.co

Source: rastreo.com.co

Avital 3100 Wiring Diagram – davehaynes.me

Avital 3100 Wiring Diagram – davehaynes.me

Source: davehaynes.me

Wiring Diagram For Led Wrap Around Light Fixture LED …

Wiring Diagram For Led Wrap Around Light Fixture LED ...

Source: www.odicis.org

Angled Surface Mount Aluminum Profile Housing for LED …

Angled Surface Mount Aluminum Profile Housing for LED ...

Source: www.superbrightleds.com

12v Wiring Basics – Wiring Diagram

12v Wiring Basics – Wiring Diagram

Source: www.anenglathi.com

Quickie Projects

Quickie Projects

Source: www.ladyada.net